| HOME  | PRODUCTS  | COMPANY  | TECHNICAL DOCS  | CONTACT US  |     
 Home >  Products >  Portable Fiber Coupled UV LED >  Black-LED-630               

Black-LED-630

                                    USA/Canada: +1 (248) 436-8085


 Fiber Coupled Blue LED Light Source


 Introduction

This new compact fiber-coupled high power RED LED light source module at 630nm is an effective replacement of lasers and lamps in many applications, such as spectroscopy, inspection and component texting. This new member of the modular OptiBlocks family provides >18mW of CW power at fiber output (2000 micron core POF fibers).

The LED driver supports CW or external TTL modulation with user controllable frequency and duty cycle.


black led

 Features:

  • High Power
  • Speckle free
  • LED spectrum can be narrowed by optional band pass filter
  • Compact and robust head: 50mm x 50mm x 40mm
  • Reciprocal SMA, FC or ST fiber connection
  • TTL external modulation
  • Precisely adjustable power
  • Long life (no lamp or laser tube replacement required)

 Replacement of:

  • He-Ne red lasers
  • Red Diode lasers
  • Lamps

 Applications:

  • Spectroscopy
  • Fluorescence excitation Alexa Fluor 633, 635, Cy5, SYTOX Red
  • Bio analysis
  • Component test and inspection

 Specifications

Peak wavelength: 635±5 nm Typ.

Centroid: 630±5 nm Typ

Spectrum half width:20 nm Typ

Power output:

Black-LED power output is limited by the reciprocal fiber characteristics.

Larger core and higher NA will increase maximum power output, and vice versa.

630nm Spectrum
 The table below shows a few examples of the CW output power at different fibers:
Fiber brandFiber type*¹ NAFiber Core Diameter Output Power Typical*²
Mitsubishi Rayon Super Eska SH8001 POF 0.5 2000 µm 18 mW
Mitsubishi Rayon Super Eska SH6001 POF 0.5 1500 µm 15 mW
Mitsubishi Rayon Super Eska SH4001 POF 0.5 1000 µm 13 mW

*1: Fiber length ~ 1 m; POF – Polymer Optical Fiber

*2: The measurement done by Ophir Nova II power meter equipped with PD300-UV head. The wavelength is set at 630 nm. The values are for non filtered Black-LED-630.

 Optical output connector:


 The Black-LED is available with SMA, FC or ST reciprocal fiber connector.

Dimensions:
Black-LED head: 50mm x 50mm x 40mm
Black-LED controller: 75mm x 40mm x 120mm (W x H x L) without key switch
and other extrusions
Power adaptor: 60mm x 35mm x 10mm (W x H x L)



 Benchtop LED Current Controller

 Introduction



The Benchtop LED current controller has been designed to provide precisely controllable, low noise current for driving a variety of LEDs. The current controller can be configured to drive virtually any currently available LED including the high power LEDs. in constant current (CW) or chopping mode defined by external TTL input.

Controller

 Specifications:


Output current control range: 0-1000 mA

Output voltage: 1-15 V

Chopping frequency: DC – 10 KHz

Connector for LED: 9-pin D-type

Connector for TTL input: BNC

Input power supply: 24 VDC, 1 A

Power adaptor input: 100-240 VAC, 1 A, 47-63 Hz

Dimensions:

Controller: 75mm x 40mm x 120mm (W x H x L) without key switch and other extrusions

Power adaptor: 60mm x 35mm x 10mm (W x H x L)

© Prizmatix, Israel